- Which To Buy?
- About US
Essengen-F is a topical finasteride only product (without minoxidil).
This product has 0.2% finasteride, equivalent to 1 mg finasteride per 0.5 ML of solution.
One unit is 2 oz (60 ml), sufficient for 4 months of supply with once daily usage (0.5 mL per application).
If you have a large hair loss area and 0.5ml is not sufficient to cover it, you can use our PG Solvent to dilute this product to make 0.1% finasteride. Therefore, you can use 1 ml and still receive 1 mg per application.
This is a fast drying, non-grease topical product. It dries in a few minutes.
This product is also convenient for those who want to receive more than 1 mg finasteride daily dosage.
Following is the volume/dosage exchange rate.
0.5 mL: 1 mg finasteride
1.0 mL: 2 mg finasteride
2.0 mL: 4 mg finasteride
0.2% Finasteride ( 2 mg of finasteride in every 1 ML).
Using the included dropper, apply up to 0.5 mL Essengen-F directly on the scalp in the hair loss area, once daily.
Want to find out the most suitable product for you? Check out the comparison of different products here: https://www.minoxidilmax.com/Best-minoxidil-products-for-hair-regrowth
If you want to use both Finasteride and minoxidil, you can choose Essengen-6 Plus, Dualgen-15 NO PG Plus, or Dualgen-15 With PG Plus, Essengen-6 Plus is particularly suitable for those who never used but want to start a minoxidil and finasteride combo solution.
How long does one unit last?
A: One unit is 60 ml (2oz). If you used 0.5 ml per application as recommended, it will last for approximately 4 months. It costs less than one dollar a day.
I found that 0.5 ml is not sufficient to cover all the hair loss area, should I use more?
A. Please be advised that you need only a very thin film to cover the hair loss area. 0.5ml should be sufficient for most people. When applied properly, 0.5 ml should be sufficient to cover the hair loss area of a person with advanced hair loss (such as Hamilton-Norwood scale stage IV - V).
1). To make 0.1% topical finasteride, mix one unit of Essengen-F (60 ml) with one unit of PG solvent (60ml), and you get 120 ml of 0.1% topical finasteride (1 mg per ml).
2) To make 0.05% topical finasteride, mix 20 ml of Essengen-F (you can use the included dropper to measure the volume) with one unit of PG solvent (60ml), and you get 80 ml of 0.05% topical finasteride (0.5 mg per ml).
3) To make 0.025% topical finasteride, mix 8.5 ml of Essengen-F with one unit of PG solvent (60ml), and you get 68.5 ml of 0.025% topical finasteride (0.25 mg per ml).
3) To make 0.005% topical finasteride, mix 1.6 ml of Essengen-F with one unit of PG solvent (60ml), and you get 61.6 ml of 0.005% topical finasteride (0.05 mg per ml).
How long will I see results?
A: It usually takes 3 to 4 months to see results. In other words, you should see some difference after finishing one unit. Consistency is the key to the success. To obtain the best result, it is important to use it every day. It is recommended to use it in the evening and wash your hair in the morning (no need to use shampoo every time. Rinsing out with water will be fine).
Will I experience any regression if I switch from finasteride pill to Essengen-F?
A. This is product is perfect for those who are taking finasteride pills and concerned about its side effects. One is not expected to have any regression as a result of switching from finasteride pill to Essengen-F.
Is this product stable? Can I stock more than one year of supply?
A. The product has a shelf life of 3 years when stored at room temperature. It is perfectly fine to purchase one year of supply (3 units) at a time. No need to store in a refrigerator.
Why should I use this Essengen-F instead of finasteride pill?
A. The shorter answer is that Essengen-F works the same as finasteride pill (Propecia as brand name) while less likely to have side effects. That is because the topical formulation has more of a localized effect, so systemic side effects (side effects which effect the entire body), such as decreased libido; erectile dysfunction and those seen with oral form may be avoided. For more detailed information, read here.
I have a large hair loss area. 0.5 ml is not enough to cover all the area. What should I do?
A. 0.5 ml should be able to cover a pretty large area when it is applied properly. In addition, it is not necessary to cover all in each application. You can alternate the areas in different applications to ensure the product is evenly distributed overall.
You can also mix 2 oz Essengen-F with 2 oz of PG solvent. You end up with a 4 oz 0.1% topical finasteride solution, which will allow you to use 1.0ml per application per day and one unit still lasts for 4 months. You can order the PG solvent here.
How can I make a lower concentration of topical finasteride?
A. The concentration of finasteride (0.2%) in this product is suitable for the majority of people. Some people who are super sensitive to finasteride may want to have a lower concentration. This can be easily achieved by mixing this product with our PG Solvent.